LUX ELEMENTS - SYSTEMS FOR BATHROOM DESIGN

Shapes

Bath tubs are available in countless variants. The standard range is therefore limited to cladding elements for standard rectangular bath tubs. In addition, LUX ELEMENTS produces alternative shapes and sizes for all installation situations. Round, oval or pologonal, one of a kind or a series.

The TOP-TR system enables:

• Combination of pre-designed components and technical articles
• Individual planning
• Combination of individual planning and standard articles

TOP-TR PLUS – examples

TOP-TR PLUS – example: the cladding of an elliptical shaped bath tub

1The prefabricated parts are leveled parts with a sprit level. Afterwards the dimensional and fitting accuracy is checked.

2The height adjustment of the cladding elements is made with the help of adjustable feet.

3Then the holes are pre-drilled through the cladding after which it is removed and the holes are drilled fully.

4Dots of COL-AK fixing adhesive are applied on the rear of the cladding where the holes have been drilled.

5Then the cladding is glued with its rear side to the wall and anchored with FIX-FID hammer fix plugs.

6The bath tub is inserted when all fixed parts are anchored. The pipes are connected afterwards and the remaining loose elements are glued to the elements anchored on the wall. The COL-MK mounting adhesive is used for this.

• With footboard and ledge
• Mounting by means of metal plug connection
• Additionally held by magnets in case of round shapes
• Easily removable for maintenance and repair
• Available as a made to measure product

Mounting by means of metal plug connection

Whirlpool shapes – all whirlpool claddings are equipped with footboard and ledge:

1Rectangular and straight shapes – TOP-WP G

2Quadrant shapes – TOP-WP V

3Hexagonale shapes – TOP-WP S

4Oval shapes – TOP-WP O

5Trapezoidal shapes – TOP-WP T

Platform for corner installation – TOP-WP P

• Suitable for whirlpool cladding TOP-WP S 1900
• For compensation of the cavity behind the whirlpool tub

LED lighting – TOP-WP LI

• LED light rope warm white
• Made-to-measure for each whirlpool cladding – TOP-WP

Maintenance opening – TOP-WP REV 300

• Supplied loose, incl. appropriate milling in the whirlpool cladding

Mounting accessories for whirlpool claddings – TOP-KIT WP
consisting of:

• 10 hammer fix plugs – FIX-FID 110
• 20 screw plugs – FIX-SD 80
• 1 cartridge mounting adhesive – COL-MK

Shapes

Whirlpools are available in countless variants. The standard range shows only a small selection of possible options. In addition, LUX ELEMENTS produces alternative shapes and sizes for all installation situations. One of a kind or a series.

The TOP-WP system enables:

• Combination of pre-designed components and technical articles
• Individual planning
• Combination of individual planning and standard articles

TOP-WP PLUS – examples

1Washstand paneel – hard foam support element without or with recess and drainage system (linear drainage)

2Drilled holes (optional) – for the use of the stainless steel brackets in case of a floating design, positioning and number depends on the model

3Stainless steel brackets (optional) – with mounting plate for floating design, number and length depends on the model

Cover rail / channel drain – dimensions: 70 x 650 mm
Special features: reversible cover rail for two design variants (brushed stainless steel and tileable rear side), tiling aid for clean tiling, height adjustable from 5 – 17 mm using height adapter, with odour trap

LUX ELEMENTS LAVADO® – accessoires (optional)

Indirect lighting - A matching light rope including power supply unit is optionally available for all LAVADO-FLOAT washstand models. This is installed on the underside, thus creating pleasant, soft room lighting. If there are drawers or cabinets under the washstand, the light provides a better view.

Reinforcements – Washstands made of hard foam support elements are particularly light. Nevertheless, a combination with additional components on the side or under the product is no problem at all. E.g., if a towel rail or an under-sink shelf is to be attached, the mounting surface on the washstand is stabilised with a plastic reinforcement in the factory. This can also reliably withstand high loads.

• 3 design variants – for fitted or top-mounted basins, with point or linear drainage (incl. milling)
• Individual dimensions and shapes
• Floating design (optional)
• Design variant LAVADO L 650:
  • Channel drain (70 x 650 mm) integrated at the factory, incl. horizontal drain support (DN50) and odour trap
  • Two design options due to a reversible channel cover rail
• Incl. 1 cartridge (290 ml) mounting adhesive – COL-MK
• Accessories (optional):
  - Stainless steel brackets, for a floating design – LAVADO K
  - LED light rope for the indirect lighting – LAVADO LI-WW
  - Reinforcement, for stable fastening – LAVADO PRO-MAK
  Details

Basic principle

1Stainless steel brackets (optional) -  for a floating design positioning, number (2 or 3) and length (300 or 450 mm) depending on the individual model

2Washstand panel - hard foam support element, different dimensions (W x D x H) 3 design variants: even (G), point drainage (B) or with linear drainage (L)

Design variants

Even –
LAVADO G

System components

1Washstand panel – hard foam support element, incl. custom milling, e.g., for top-mounted fittings, at the drain position, or for the acceptance of a fitted basin.

Point drainage –
LAVADO B

System components

1Washstand panel - hard foam support element, with point drainage, including custom milling, e.g., for top-mounted fittings and a recess

Linear drainage –
LAVADO L 650

System components

1Cover rail – brushed stainless steel, tileable on the rear side

2Tiling aid – brushed stainless steel for clean tiling

3Height adapter – separately provided for height adjustment from 5 – 17 mm

4Odour trap – integrated into the drain frame

5Channel drain – DN50, 70 x 650 mm

6Washstand panel – hard foam support element, with sloping recess

7Connection technology – adhesive adapter DN50 to 1¼“ external thread, 90° elbows

Brackets – LAVADO K

• For a floating design
• Stainless steel, with mounting plate
• 2 lengths (300 und 450 mm) – for different depths of the washstand
• Installation possible on masonry and stud frames

The principle

NOTE – please observe: An individual washstand in a floating design always consists of 1 washstand panel LAVADO PLUS and at least 2 LAVADO-K brackets! Please take this into account when ordering.

• Required quantity (brackets) for LAVADO PLUS with width
≤ 1500 mm = 2x LAVADO K …
≤ 2100 mm = 3x LAVADO K …

• Required article ( brackets) for LAVADO PLUS with depth
≤ 480 mm = LAVADO K 300
≤ 600 mm = LAVADO K 450

Mounting principle – floating Design (optional)

1on stud frames

2on masonry

LED-lighting – LAVADO LI-WW

• LED light rope warm white
• For the indirect lighting of the long side underneath the washstand
• Protection class IP67
• Incl. 5 m supply cable, power supply unit

Reinforcement – LAVADO PRO-MAK

• for the stable fastening of e.g. fittings 1, drainage technology 2 or additional components  3 (towel rail, under-sink shelf etc.)
• factory-integrated

Would you like a non-standard washstand? No problem! Whether extra storage space, an adapted recess cut-out or an alternative drain variant: LUX ELEMENTS manufactures your desired washstand as a custom-made product, including any necessary adaptations for under-sink cabinets or drawers.

Individual shapes and equipment

Washstands in a floating look are available in countless variants. LUX ELEMENTS produces alternative shapes and sizes.
Round or rectangular, compact or delicate, one of a kind or a series. The drainage technology is also flexible: Unlike the channel of the standard model, a channel drain with an extended cover rail is available.

The LAVADO PLUS system enables:

• Combination of pre-designed components and technical articles
• Individual planning
• Combination of individual planning and standard artic

LAVADO PLUS – examples

• 2 basic shapes – straight or round
• Construction kit consisting of bath tub and substrate element
• Individual dimensions
• Including floor drain fitting frame, drain and overflow fitting
• Incl. design grate „VARI“ (tileable)
• Compatibel with all LUX ELEMENTS®- TUB-RA …- grate variants

Design grate „VARI“, tileable – TUB-RA-DV

Inlay elements – RELAX-BW LE / RELAX-BW LR

• 2 design variants:
  - straight – RELAX-BW LE
  - round – RELAX-BW LR
• can be installed on one or both sides

Mounting accessories – RELAX-BW KIT

• Necessary mounting material for installation in one kit

Inlay elements (am Beispiel RELAX-BW LE)

Would you like a non-standard bath tub? No problem! Whether an unusual shape or unique installation situation: LUX ELEMENTS manufactures your custom-made product..

Shapes

Bath tubs are available in countless variants. The standard range shows only a small selection. In addition, LUX ELEMENTS produces alternative shapes and sizes for all installation situations. One of a kind or a series.

The RELAX-BW PLUS system enables:

• Combination of pre-designed components and technical articles
• Individual planning
• Combination of individual planning and standard articles

RELAX-BW PLUS – examples

RELAX-BW PLUS – from planning to finished item

Idea and planning – Customer's idea, sketch or detailed plan, preparation of a technical drawing for approval with 3D view at LUX ELEMENTS

Order and production – Manufacture of the individual components exactly in accordance with planning specifications. Test assembly at LUX ELEMENTS and numbering of the components

Assembly and arrangement – Delivery to the building site in segments. Fast assembly of the prefabricated components by the installer

• 3 sizes
• Prefabricated niches with or without shelves
• Vertical or horizontal installation

Niches – accessories (optional)

LED-lighting– RELAX-NI LI-WW

• LED light rope warm white
• Suitable for niches RELAX-NI, tailored to the installation situation (vertical or horizontal)
• Protection class IP67
• Incl. 5 m supply cable, power supply unit

• Prefabricated bench seats for bathroom and shower areas as building kit
• Accessories (optional):
  • Backrest in two design variants
  • Factory-installed seat heating
  • SHAPE and SIZE: LED light rope

System components

1Seat element – 3 design variants without (SOLO) and without (SHAPE, SIZE) milling for LED light rope

2Side elements – hard foam support element, 50 mm

3Fillers - hard foam support element, 50 mm, number depends on the length of the bench

Design variants

Backrests – RELAX-BA-L

• Backrest, 2-piece, in two design variants:
  - with rounded surface – RELAX-BA-L R
  - with level surface – RELAX-BA-L E
• To suit the bench form SOLO, SHAPE and SIZE

Design variants

Heating – RELAX-BA HE-E / HE-E L

Seat heating – RELAX-BA HE-E

• Factory-installed heating mat for bench form SOLO, SHAPE and SIZE
• Incl. electronic temperature controller with time control
• Protection class IP30 (not suitable for damp rooms)

Backrest heating – RELAX-BA HE-E L

• Factory-installed heating mat for backrest BA-L R and BA-L E

LED lighting – RELAX-BA LI-WW

• LED light rope, warm white
• To suit the bench form SHAPE and SIZE
• Protection class IP67
• Incl. 5 m supply cable, power supply unit

Prefabricated shower partition wall elements in two sizes:

• 2500 mm high, 900 mm wide – RELAX-TW 900
• 2500 mm high, 1200 mm wide – RELAX-TW 1200

Design variants

Shower partition walls – accessories (optional)

Individual niche milling – RELAX-TW NI

• 96 mm deep

LED lighting – RELAX-TW LI-WW

• LED light rope warm white
• Suitable for RELAX-TW NI
• Protection class IP67
• Incl. 5 m supply cable, power supply unit